Victron SmartSolar 100 15 MPPT solar controller

Victron SmartSolar 100/15 MPPT

Robust and fast MPPT controller for demanding conditions with panel voltage up to 100 V, maximum charging current 15 A. Battery 12/24 V, PV max. 220/440 Wp. Built-in Bluetooth and VE.direct interface.

Ultra-fast Maximum Power Point Tracking (MPPT)

Victron Energy MPPT solar controllers are among the absolute world leaders in this field and offer ultra-fast MPPT tracking. Especially in cloudy skies with continuous changes in the intensity of illumination, thanks to this controller, solar gains are 30% higher compared to classic PWM controllers or 10% higher compared to slow MPPT controllers. Excellent efficiency of up to 98%, without unnecessary energy losses with silent passive cooling without a fan.

The maximum permitted panel power for 12 V systems is 220 Wp, for 24 V systems 440 Wp. If these values ​​are exceeded, the controller automatically reduces the incoming power from the panels to acceptable values, so that the excess power does not damage the controller. The solar controller is factory preset and there is usually no need to make any major adjustments to the settings. The maximum open circuit voltage (referred to as Voc) of the connected solar panels must not exceed 100 V. Attention! The voltage of the solar panels increases with decreasing outdoor temperature. The maximum input short-circuit current of the PV panels must not exceed 15 A, otherwise permanent damage may occur.

The new line of SmartSolar MPPT controllers offers built-in Bluetooth

This new feature brings the possibility of connecting your "smart" phone/tablet with your "smart" solar controller. You can monitor many system parameters and historical statistics for the last 30 days. You also have the option of setting operating parameters.

Download the free VictronConnect mobile app for iOS or Android. If you want to do the above using a PC, you can use the VE.direct to USB cable to connect the controller and the PC. You only need to install the Victron Connect program on your computer.

The internal electronic components are protected by a resin coating against adverse effects and for a long service life. This offers increased resistance to IP43 for electronic components and IP22 for connection connectors. Designed for vertical position on a non-flammable surface, with wiring from below. The controller contains an internal temperature sensor for appropriate adjustment of the charging voltage. Automatic detection of system voltage 12 or 24 V.

Adaptive three-stage charging

1. fast charging (Bulk), 2. absorption (Absorption) and 3. maintenance (Float). Initially, during fast charging, a high current and a lower voltage are generated to quickly recharge a discharged battery. This phase is followed by a constant voltage with a decreasing current to fully charge the battery without dangerous overcharging, which reduces the battery life. The charged battery is kept charged with a very low current and low voltage. If the battery voltage drops below 13.2 V, for example due to a load, a new charging cycle is started.

The voltage from the panels must exceed the battery voltage by 5 V for the controller to start working and charging the battery. The controller charges until the voltage from the panels is 1 V higher than the battery voltage. For a 12 V battery, we recommend panels with a minimum number of 32 cells and a maximum number of 108 cells (panels in series). It is therefore possible to charge a 12 V battery and panels with an operating voltage of 24 V. For 24 V systems, we recommend panels with a minimum number of 72 cells and a maximum number of 108 cells. The purpose is to achieve sufficient voltage for efficient and full charging of the battery.

The solar controller has a DC output for powering DC loads. The DC output voltage is equal to the battery voltage. So if you have, for example, a 12 V battery - we can power a 12 V load on the DC output.

BatteryLife algorithm - adaptive charging to extend the battery life. The controller constantly monitors the battery charge level and day after day gradually increases the voltage level at which the load is disconnected until the absorption voltage is reached (the battery is fully charged). This is followed by a decrease in the voltage level at which the load is disconnected. In this way, the battery can be fully charged about once a week even with reduced solar gains and higher loads, which will have a positive effect on the battery life. This is an optional function.

Warning

• Victron Energy MPPT controllers are not allowed to be used in combination with photovoltaic panel optimizers. When used
• MPPT controllers and optimizers may be damaged and this damage may not be recognized as a legitimate complaint.

Battery voltage: 12/24 V auto-detect

Maximum battery current: 15 A

Maximum PV power, 12 V: 220 W

Maximum PV power, 24 V: 440 W

Maximum PV voltage (open circuit): 100 V

Maximum short-circuit current: 15 A

Efficiency (max.): 98 %

Weight: 0.6 kg

Dimensions: 113 x 100 x 50 mm